How to Take Down a Ceiling Fan? Here’s how To Do It Safely

1

Flip off the circuit breaker that controls the ceiling fan. Mount a ladder below the fan. Verify that no electrical energy is coming into the system with a non-contact circuit tester held close to the motor, checking for an absence of chirps or flashing lights.

Video

Eradicating A Ball And Socket Ceiling Fan

1. Turn off the electrical power on the electrical panel. 
2. Utilizing the step ladder, take away the metallic cover protecting the mounting bracket. Unscrew the screws to take away this, and have in mind you could want to make use of a brief screwdriver to achieve all of the screws. Decrease the cover to relaxation on the fan. 
3. Take a look at to ensure there isn’t a electrical present utilizing your voltage tester. 
4. Take away the wire nuts, and the wires. Put the nuts again on the wires coming from the ceiling as it would stop any accidents if you must flip the facility again on. 
5. Maintain the fan tightly, and slide the ball on the high of the fan pole out of the mounting bracket. 
6. Decrease the fan to the bottom, or cross to a helper, in case you have one. 
7. The mounting bracket is often hooked up to {the electrical} field by two screws. Unscrew them and take away the bracket. Put the screws again into {the electrical} field to ensure they don’t get misplaced.

Nice learn: ceiling fans for bedrooms

Step 11: The Ending Touches

All that’s left to do is set up the bulbs after which place the shade or mild cowl excessive. When you’re assured that all the things is the place it ought to be, activate the circuit breaker to that room and provides the sunshine swap a take a look at.

Step 9: Tightening the Wire Nuts

With the wires correctly paired up with each other, all that’s left to do with them is canopy them and tuck them away. Screw a wire nut over every of the twisted wire naked ends. You wish to tighten the wire nuts till they really feel tight however watch out to not overtighten.

While you over-tighten these wire nuts it may possibly strip them, loosening the connection. When that occurs, the connection can arc and are available aside. With the wire nuts safe, tuck them rigorously again into {the electrical} field.

Breaking Down the Fan

Along with your ladder in place and your screwdriver in hand, you may start to take away the parts of your fan. The sunshine kits that include most ceiling followers will be eliminated (usually unscrewed) by hand. Take that off first. When you get to the fan blades, you will want your screwdriver.

How Do I Take away Ceiling Fan Blades?

With the sunshine fixture out of the best way, you’ll have a lot simpler entry to the fan blade attachments. Relying on the configuration of your ceiling fan, the screws that maintain the fan blades in place could also be dealing with you or the ceiling. Use the screwdriver to take away the screws and every fan blade separately. Most fan blades can have two screws every.

4

Study the mount beforehand hidden by the cover to learn to disengage the motor and its housing. You could have to push a pin out of a help bracket and dangle the motor on a wire help hook in-built to help the motor, whereas the installer wires the system. Alternatively, a security cable might run from a screw within the joist above to the ceiling fan downrod, which is screwed into the highest of the motor housing. Ideally, seek the advice of producer’s literature earlier than you mount the ladder to find out if the aforementioned pin, or alternatively a ball notch or different connector, hyperlinks the downrod to the mounting bracket.

4.  Separate related ceiling fan wiring

With downrod followers, you’ll must take away the cover first. Then you may start eradicating the wire nuts and disconnecting the fan wires from the home wires. In case your ceiling fan has a distant receiver wired within the cover, be sure you take away the wire nuts and disconnect the distant receiver wires from the fan and ceiling. 

When you take away the sunshine and blades out of your low-profile followers, you may take away the cover to start disconnecting the wires from the fan, ceiling, and any distant receiver. Low profile ceiling followers usually connect to the mounting bracket from a hinge on one aspect you can relaxation the fan, making it simpler so that you can use each palms for unwiring the ceiling fan.

NOTE: If you’re uncomfortable with the wiring portion of eradicating a ceiling fan, seek the advice of with a licensed, skilled electrician.

Security Ideas

There are some security suggestions that it’s best to at all times have in mind when working with electrical energy inside your house. 

• Most circuit breakers can have separate circuit breakers for various areas of your house. In the event you can’t discover the proper one, flip off the principle breaker. Some circuit breakers have a lock that may stop others from turning the breaker again on. If yours has a lock, use it. 
• If your house has a older mannequin fuse panel, take away the fuse. In the event you can’t discover the proper circuit, shut down the facility to the entire home. Maintain one hand in your pocket when eradicating the fuse, so that you simply’re not dealing with it with each palms. 
• You might also wish to depart a observe on the distribution field to let any electrical workmen know that you’re engaged on the circuit. 
• At all times test that the circuit is lifeless earlier than you start engaged on any wires. Use a socket tester, or a voltage tester. 
• As rubber doesn’t conduct electrical energy, put on rubber soled sneakers or boots. 
• Be sure to use prime quality instruments, equivalent to pliers, and screwdrivers, as cheaper high quality instruments might snap or break, inflicting accidents. 
• Additionally, ensure that your instruments have rubber coated handles to assist stop any electrical energy going by means of your physique. 

Tags