How to Replace a Kitchen Sink and Faucet

Choose up key elements on the ironmongery store earlier than you begin

Substitute a Kitchen Faucet Photograph 1: Take away the drain strains from the tap Disconnect the drain strains and P-traps in the event that they block your entry to the tap and water provide pipes. (Place a bucket or espresso can below the P-trap to dump residual water after you pull it free.)

Likelihood is, you’ll must make a couple of journey to the ironmongery store for elements to learn to exchange a kitchen faucet, however to provide your self a combating shot at finishing the job with one-stop buying, seek the advice of this listing. We’ll present you tips on how to take away a kitchen faucet with the steps on this article.

• Shutoff valves Earlier than you store in your new faucet (see “Deciding on a Faucet” on the finish of this tips on how to exchange a kitchen faucet article), have a look below the sink and make it possible for there are shutoff valves feeding the tap. In case you don’t have shutoff valves, add them. You probably have them, affirm that they’re in working order by turning on the cold and warm water on the faucet and shutting off the valves. If the tap nonetheless drips, set up new ones. More than likely you’ve gotten 1/2-in. copper provide pipes. In that case, add easy-to-install solderless “compression becoming” valves (Images 9 and 10) to your buying listing. But when not, purchase whichever valve sort is suitable together with your pipes.

• Provide tubes: Subsequent, measure the prevailing provide tubes and purchase new chrome steel–sleeved provide tubes (Photograph 9). They’re designed to provide rupture-free service for years and may be routed round obstacles with out kinking.
• Basin wrench: Additionally purchase a basin wrench ($15; Photograph 4). This bizarre little wrench is made particularly for eradicating and putting in these hard-to-reach fasteners that clamp older faucet assemblies to the sink. (Newer taps have plastic Wing-Nuts that may normally be loosened and tightened by hand.) A basin wrench’s spring-loaded jaws pivot so you’ll be able to both loosen or tighten nuts in tight areas.

If you have to take away drain strains to entry the tap, get a pipe wrench or slip-joint pliers (Photograph 1). For chopping copper tubes, purchase a traditional tubing cutter. But when your copper provide strains are inside a number of inches of the again of the cupboard, purchase a particular mini tube cutter (Photograph 3). You’ll additionally want a set of open-end wrenches for disconnecting and hooking up the water strains.

Earlier than disconnecting the drain strains, take a snapshot or make a sketch of the format that can assist you put all of it again collectively.

Take away a Kitchen Sink TIP: Plan on changing your faucet throughout retailer hours. Likelihood is higher than 50/50 you’ll want a minimum of another half for this tips on how to exchange a kitchen faucet venture.

Take away a Kitchen Sink TIP: Prop up a scrap of plywood on some 1-qt. paint cans in entrance of the cupboard. You’ll be rather more snug mendacity below the sink throughout this tips on how to exchange a kitchen faucet venture. In any other case, the sting of the cupboard could be digging into your again

Video

Now set up the brand new faucet

Photograph 5: Place the flange over the tap opening

Observe any producer’s preassembly directions and place the elective flange (see Photograph 8) over the tap opening. Finger-tighten the flange nuts beneath the sink and verify the alignment of the flange, faucet and sink gap from above.

Photograph 6: Tighten the tap mounting nut

Examine the operation of the tap and deal with to verify you’re not placing it in backward, and thread the feeder strains by way of the flange and sink holes. Then slip on the tap washer, and thread on and tighten the faucet-mounting nut from under, gently spreading the tap provide tubes if needed to achieve device clearance (generally producers present a particular device for this).

Photograph 7: Tighten the flange nut

Hand-tighten, then cosy up the flange nuts with an open-end wrench. You’ll be able to solely flip the wrench a couple of one-sixth revolution at a time.

Photograph 8: Connect the spray hose to the tap provide tube

Thread the spray nozzle line by way of the tap physique, then thread the spray hose becoming onto the tap provide tube and tighten it. Pull the nozzle out of the tap to ensure the hose below the sink operates freely, then connect the counterweight following the producer’s directions.

Photograph 9: Mark the availability strains the place you wish to minimize them

Tighten the brand new valves onto the availability tubes and mark the feeder strains simply above the compression nuts on the valves for cut-off.

Photograph 10: Join the availability tube to the availability strains Clear the copper tubing with nice sandpaper, then slip the nut, compression ring and valve physique over the pipe and tighten. Shut the valve, activate the principle water valve and verify for leaks. Place a bucket below the tap and switch the tap on to verify for leaks. Reassemble the rubbish disposer, P-traps and drain strains.

Observe the producer’s instructions to mount the brand new faucet, then remount the sink (with the brand new faucet) and hook up the water strains as we present on this tips on how to exchange a kitchen faucet venture.

TIP With most taps, solely three of the 4 holes are coated, so that you’ll both must get a clean insert or use the additional gap for a liquid cleaning soap or on the spot sizzling water dispenser. Plan to do the set up when you’re below the sink with every thing torn aside. You probably have a leaking faucet, seek the advice of this text on tips on how to repair a leaky faucet.

Deciding on a faucet Whenever you’re shopping for a faucet (as with most different issues), you get what you pay for. Taps that price lower than $100 could also be product of chrome-plated plastic arts with seals and valves that put on. They’re OK for light-duty use however received’t rise up lengthy in a regularly used kitchen sink. Taps that price greater than $100 typically have stable brass our bodies with sturdy plating and washerless controls that’ll give leak-free service for a lot of, a few years. Some even include a lifetime guarantee. High quality continues to enhance as much as about $200. Spend greater than $200 and also you’re principally paying for type and end. Keep on with model title tasks so substitute elements will likely be simpler to seek out—within the unlikely occasion you’ll ever want them.

STEP 2: Place the tap within the holes

Attaching the tap to the sink is fairly straightforward. After the gasket or putty is in place, set the tap into the right holes. Place your self below the sink, and screw on the plastic nut. In case you’ve used plumber’s putty you’ll be able to clear away the surplus with a putty knife or use a finger.

Instruments Supplies

• 

  Adjustable wrench

• 

  Pliers

• 

  Screwdriver

• 

  Putty knife

• 

  PVC pipe noticed

• 

  Nut driver

• 

  PVC pipe cutter

Measure for New Faucet

1. Take measurements of the previous sink to find out what type of recent faucet will match. For instance, some have three holes in a row. Others solely have two for separate sizzling/chilly valves. The spacing between the holes might differ, so be certain the brand new faucet has the proper spacing. Additionally, take into account a faucet with an extended or shorter neck than the present one. This will add to the utility and general look of the completed lavatory.

Remaining Ideas

Changing a faucet is a reasonably straightforward DIY venture that may take about an hour to finish. With a view to make sure that it doesn’t find yourself taking lots longer, it’s vital to ensure the brand new faucet requires the identical variety of mounting holes and that every one the provides that aren’t included with the brand new faucet are readily available when starting the set up.

Commercial

In with the brand new

There are a number of configurations for taps. Between the variety of handles, spray nozzle varieties and even spacing of required holes, there are a number of methods to customise. Before you purchase a brand new faucet, take into account your association, particularly the present quantity and site of holes in your counter or sink. Sinks and counter tops may be modified accordingly, however you may must perform a little analysis prior to buying your new faucet. 

Enlarge Image

Begin by placing the bracket that matches between the counter/sink and tap in place. These will usually have a foam underlay that may type a seal to assist forestall water from seeping beneath the tap meeting. Some taps might differ, however the faucet I put in required minimal meeting previous to set up. 

Run the availability strains of the tap meeting, adopted by the threaded rods of the tap, by way of the holes in your countertop or sink. Working beneath in essentially the most snug place you’ll find (good luck), tighten the retaining nut with a wrench. 

If no socket wrench was supplied with the tap, and the area is tight sufficient to require a basin wrench, be extra-careful to not harm the tap’s water provide strains. It relies on the configuration of your specific faucet, but when the water strains are in the way in which of the retaining nut It may very well be useful to wrap them with nylon tape or another protecting materials earlier than doing this. Damaging water strains may trigger a leak, and the entire mayhem that comes with that. You don’t need that.

Set up a New Faucet

1. Observe Your New Faucet’s Instruction Guide Your new faucet ought to include step-by-step instructions from the producer, however you must start by including the tap gasket to the underside of the tap. Learn your new faucet’s instruction handbook to see if plumber’s putty is required along with or instead of the gasket.

2. Put Your New Faucet in Place

Subsequent, put the tap by way of the mounting holes within the sink and tighten the mounting nuts below the sink to make the tap keep in place.

3. Set up a Matching Drain

In case you’re seeking to replace your sink drain and plumbing under the sink floor, we have compiled detailed instructions How to Install a New Drain. The following tips and tips will enable you to alleviate any present leaks, or just assist to replace your sink’s plumbing as a solution to keep away from any future points which will come up.

Changing an previous faucet can get difficult, and you could want some assist to get the job achieved. Following our step-by-step instructions to take away the tap and studying your instruction handbook in your new faucet will go a great distance that can assist you get this venture completed all by your self. Your new faucet will certainly assist to replace your lavatory and provides it a brand new look, in addition to guarantee your lavatory is working nicely with no leaks or points to trigger issues for you. For much more assist, view this video that gives you detailed instructions for the complete means of eradicating and putting in a brand new faucet. For extra ideas, go to Set up a Drain.

Whereas do-it-yourself tasks may be enjoyable and fulfilling, there’s all the time a possible for private harm or property harm. We strongly counsel that any venture past your talents be left to licensed professionals resembling electricians, plumbers, and carpenters. Any motion you’re taking upon the data on this web site is strictly at your individual threat, and we assume no duty or legal responsibility for the contents of this text.

Tags